BUILD TUNE RACE RC YACHTS
Craig Richards setup guide 2
The bible for setting up the A, B rig and C rig

Craig Richards Tuning guide (Page 2)
A Rig forestay tension:
The A rig is the only suite where I change forestay tension. The rest have the forestay as tight as I can get it until I start worrying about breaking the boat or having the mast go out of column.
You never want the forestay to pump or flog upwind, so for each increasing wind condition you go just a bit tighter so that you get a bit of sag, but no pumping. At the very top of A, the tighter the better and do not let it sag.
The sag and a loose jib cunnigham seem to put a bit more fullness into the front of the jib and with very sensitive telltales you can see that the fuller the jib entry the longer the flow seems to stay attached to the leeward side of the jib. This is particularly helpful in very dirty air with lots of wind switches etc.
The forestay length on my boat varies from 1138 to 1132mm from the lightest to strongest conditions. My go to setting when I am unsure turns out to be 1135 just as the rigging guide suggests.
It will also depend on how much your backstay stretches, I use the below on my backstay:

As Per Krabbe has kindly pointed out, dyneema lines are prone to shrinking. I have marks to quickly put the rigs into the boat (last minute change before heat etc), which I do check before each regatta, but over a few days the lines may still change length.
I have a fairly good feeling now for what the rig should look like, but it's probably a good idea to check the lengths regularly.
This is how I set up my main sheeting angle on the A rig:
I put the palm of my hand against the aft quarter of the boat and when sighting from astern I have my fingers parallel to the backstay. With my hand in this position the main boom just touches my fingers.
No measurments, no confusion and very easy to repeat.
Yes it's wider than just about every tuning guide suggests, but at this point I am just setting up consistent sheeting angles of the main and jib (to follow in next post)

With the main sheeting angle set, the jib is then trimmed such that the hole in back of the jib boom fitting is over the first knuckle on the deck. It's close to 60mm between the middle of the mast and the inner edge of the boom.
In my case its also exactly the width of my three middle fingers.

I posted some pictures Sue Brown took, but the posts seem to have disappeared.
I seem to have put the link on my main profile and not this group ..lol. http://www.flickr.com/.../in/album-72177720308506905/...
I do sail with the setting I posted. Here is my go fast mode:
I run 20mm foot depths on the main and jib as a starting point.
In this mode I want the boat to run with absolutely neutral helm. It can hunt the breeze slightly, but must never luff up and slow down. I never want to be pulling the bow down with the rudder. I may trim in and and push the bow up.
This is absolutely the best VMG mode in the absence of other boats. You will go faster and end up higher than a boat that sails only in pinch mode.
I use the bottom draft strip a lot. I want to see the maximum depth at 50% and a clean straight entry after the mast. If the fullness is further forward I flatten the foot of the mainsail further
If the boat is running with a bit of weather helm as the breeze increases I will first flatten the main off to about 10mm and if that does not work I will change the trim to let the main out slightly further, but leave the jib the same. I will also flatten the jib down to 10mm at the very top end of A, but only after the main is already down to 10mm.
The neutral helm also has the advantage that when I am unsighted and cant see the boat it is still sailing flat out without my input. This is also a big advantage when the boat is too far away to see clearly.
That lower tell tale on the main is a great trim indicator. It should fly at a slight up angle on the weather side of about 20 degrees. In this photo it says I am sailing a fraction lower than optimum and I should push the boat up with the rudder.
The neutral helm has one further huge advantage. As I tack, once I am on the new heading I seldom need to keep on some weather helm until the boat gets its speed up again and starts tracking. The boat also tacks much more cleanly as a result and I stall less when I make a mistake. I.e. its much easier to get the boat going again from a bad tack.

And a great picture of John.
He sheets the main in a bit more than I do, but the jib is still quite wide. This is probably his pinch mode though and if he dropped the main slightly so the jib is over the deck knuckle we would be quite close in setup.
One difference is that the entry angle on the main on Johns boat at the first draft stripe is a bit wider than mine, so he would need to sheet a bit closer. My entry looks a lot flatter, so I can sheet the boom out a bit and still have a similar entry angle. This could be because I have a bit more mast bend coupled with less luff curve. I actively set my mast bend so that the luff at this height moves behind the mast. I.e. the luff sits on the centre line, not to leeward of the mast.
Notice how flat he now runs his main foot depth. I was running 20mm, but John looks to be even flatter.
It's also a great picture for showing the twist in the sails and a perfect example of how the twist in the jib parallels the back of the main.

Active trim:
My high mode has the jib width at 45-50mm, about 1cm - 1,5cm in from my best VMG mode.
I have the ratchet set for the mainsail trim on my radio. I Move the trim/throttle stick on the radio so that it is two ratchet clicks up. This is the radio setting that I want to see my VMG sail setting at. I use the subtrim buttons on my radio to move the sails to that setting.
With the trim all the way in I now want the jib to be at 50mm or perhaps even 45mm in very flat water. Depending on the radio, two clicks may move the trim in more than the desired 1-1.5cm so you would need to change your throttle curve. The radio I used at Fleetwood did not need it, but my newer radio moves the sheet too far and I have set a throttle curve.
If there are boats around me and I need height, I will start with the boat at two clicks out and then once it up at full speed, I start to bleed the boat up as I trim in. Often you can carry a high fast mode for a length of time, but if I hit a bad wave or header and the boat slows then its immediately trim to the two clicks position, get the speed back and then work the boat up again one or two clicks.
If I am in clear air and chasing then I found the boat very fast at two clicks out and did not trim in much
The higher trim mode is also very useful if you get THAT boat below you that is racing only you and the fleet disappears into the distance whilst they try and luff the heck out of you. Your race is still toast, but at least it does give you some time to find a gap to tack away in.
If you do have some space to leeward, then even with the wider trim you may be pleasantly surprised to see that you don't lose height and will roll over them quite quickly.

Twist
I'll try and do a bit on twist, but here is a hint that I do not have enough twist in the top of my jib.
Camber stripes are your friend.
The bottom windward telltale is running at the angle I like, but the top one suggests I have mucked up the trim. It should match the bottom as closely as possible.

Mains twist.
Finicky beast. Half a turn on the vang can make a surprising difference.
I can only suggest a starting point and then fiddle with small changes until the boat looks and behaves to your preferences. Looking at the boat from behind when the boat is on the water and using the picture of John's boat as a template would be a good start.
Looking down the backstay from behind the boat, I want the main leech to parallel the backstay between the top two battens. It was difficult to take a photo, but fairly obvious in real life.

Jib Twist.
I like the jib leech to parallel the back of the main for as far as possible. The upper third of the jib should also parallel the main entry angle as far as possible. Top of jib and upper third of main should start to luff at the same time as you head up into the wind.

Earlier I posted a near perfect picture of John Tushingham and now I hope he forgives me for posting one a bit more ugly
This was taken a month before the Globals and I think I had an edge on boat speed in this race. I never saw his boat look like this in the Globals and want to use this to point out how top sailors like him are prepared to adapt and experiment.
In this photo we have similar rake, but I am running a more bent mast, with flatter sails. A much finer entry for the main as a result, which should result in a cleaner and wider slot between the back of the main and the jib.
The difference in speed was very small, but even a cm or two of extra speed helps get your nose out in a crowded start and makes you look like a better sailor.
Compare this to his globals setup.

These two boats (5, 51) were very similar in speeds and although the jib setting looks very similar, the mainsail shapes are quite different.
It was quite gusty so you can also see how the shape changes in the gusts and lulls.
Boat no 12 is again a bit different ... possibly fuller, sheeted closer and more twisted.